WeChat QR
Home WhatsApp Email
WeChat

K08008AR0 Angular Contact Thin Section Ball Bearing – 80 × 96 × 8 mm (Open)

K08008AR0 corresponds to the KAYDON reference for LYDL PA8008, an 80 × 96 × 8 mm open angular contact bearing. A single Type A bearing supports axial force in one intended direction. Applications with reversing thrust require a reviewed support arrangement, often using opposed bearings. Back-to-back and face-to-face layouts differ in contact-line geometry and mounting behavior. State the required arrangement and matching conditions separately when ordering; PA8008 alone does not mean a factory-matched pair. LYDL supply specifications require confirmation against the assembly drawing.

Or email sales@luoyangdeeplink.com

K08008AR0 is the reference designation associated with LYDL PA8008, an open 80 × 96 × 8 mm Type A thin section bearing. When an actuator alternately pushes and pulls, bearing orientation becomes a functional part of the design. One angular-contact bearing does not acquire bidirectional thrust capacity merely because the shaft reverses rotation. This page focuses on selecting an opposed arrangement and documenting the load direction, preload and mounting condition required for the application.

K08008AR0 dimensions and LYDL supply identity

Product specificationLYDL PA8008
Bore diameter, d80 mm
Outside diameter, D96 mm
Width, B8 mm
Radial cross section8 mm
Bearing constructionAngular contact, Type A
ClosureOpen
Approximate catalog mass0.12 kg
KAYDON reference designationK08008AR0

PA8008 appears in the 8 mm section of the LYDL metric angular-contact series.

LYDL PA8008 open angular contact thin section ball bearing, 80 × 96 × 8 mm
PA8008 is supplied as an open angular-contact bearing; any matched-pair requirement must be specified separately.

Distinguish reversal of rotation from reversal of thrust

A shaft can rotate in both directions while its axial force remains in one direction. Conversely, axial force can reverse without a change in rotation. Establish these two conditions independently from the machine's operating sequence. The bearing arrangement must address the actual thrust direction rather than the motor command alone.

In an opposed pair, each bearing is oriented to support one thrust direction within the reviewed arrangement. Back-to-back and face-to-face mounting place their contact lines differently. A back-to-back arrangement generally offers greater resistance to tilting for a compact adjacent pair, while face-to-face mounting is relatively more tolerant of misalignment; neither removes the need for accurate seats.

Selection also depends on housing stiffness, spacing and the required internal condition. Do not describe any two PA8008 bearings as a matched pair without confirming how they were prepared and specified. The arrangement, matching and preload must be agreed in addition to the individual part number.

Request a PA8008 application review.

K08008AR0 radial and axial reference ratings

Reference-brand figures for KAYDON K08008AR0. They are published catalog values, not certified LYDL capacities or test results.

Capacity and calculation basisKAYDON reference value
Dynamic radial, KAYDON method4,609 N
Dynamic radial, ISO comparison method7,855 N
Dynamic axial10,689 N
Static radial9,865 N
Static axial28,469 N

The ratings are not simultaneous load allowances. The dynamic basis is one million revolutions of L10 life; static figures assume rigid shaft and housing support. Kaydon identifies ISO 281:1990 for its ISO radial comparison column. Do not mix the two radial calculation methods. Axial figures refer to the supported thrust direction of the single bearing, not an automatically rated pair.

LYDL's series table labels force values in kg; this page does not convert those entries into unconfirmed N ratings. Obtain the supplied bearing's rating basis, internal setting and lubricant limits before final selection. No model-specific speed or pair moment capacity is inferred from these tables.

A push-pull positioning mechanism

An automation fixture may clamp a component in one direction and retract against a separate resistance. Document both force cases, including changes during acceleration and release. An opposed PA8008 arrangement can be evaluated within the 80 mm-bore installation when the full loads and stiffness requirements are known.

The supporting housing must retain the relevant rings in both load directions. Review the cover and shoulder functions during reversal, and check that the surrounding structure does not become the main source of axial movement. The open bearing requires an enclosure and lubricant specification suited to the process.

Thin section ball bearing application examples across industrial equipment
Push-pull mechanisms need an arrangement that addresses both directions of axial force.

Prevent a reversed bearing from passing unnoticed

Create a section view that shows both bearings and the intended contact-line arrangement. Identify the approved orientation marks or drawing features used during assembly. Include the required spacer and clamping arrangement, with tolerances appropriate to the specified internal condition.

If matched bearings are supplied, keep the identified set together through receiving, cleaning if specified, and installation. Do not exchange one member with an unrelated sample just because its nominal dimensions match. Any replacement policy should be established with the supplier.

Check the completed assembly under controlled axial loading in both directions. Record movement at the same datum and note any change after final cover tightening. Reversing the motor without applying the relevant thrust cases is not an adequate acceptance test for a bidirectional axial support.

AR0 identification and brand comparison

PA8008 is the LYDL open bearing designation; K08008AR0 is the catalog cross-reference. The base AR0 number does not specify back-to-back or face-to-face supply. Request the arrangement and matching requirements explicitly rather than inventing a new standard suffix.

In the KAYDON metric designation, A identifies angular contact and R the standard formed circular-pocket separator. 0 means class 1 / ABEC 1F, not zero clearance or a specified preload. K is the open steel configuration here. Confirm LYDL material, cage and precision on its own supply drawing.

The NBA prefix identifies NSK angular-contact bearings in an inch family; its codes do not specify this LYDL pair.

Specify the behavior through load reversal

Agree the positive and negative test forces, displacement datum and measurement sequence. Record whether the test is made on individual bearings, a matched set or the installed mechanism. If the requirement concerns reversal error, distinguish bearing movement from couplings, screw assemblies and housing compliance. Include set identification and the approved arrangement in the delivery documentation so that purchasing and assembly use the same definition.

Thin section ball bearing inspection and protective packaging
Keep matched-set identity and orientation information with the inspection and packaging records.

PA8008 practical FAQ

Does changing motor direction mean I need two angular-contact bearings?

Not by itself. Determine whether the axial force reverses and how it is reacted by the existing supports. Rotational direction and thrust direction are separate design inputs. Provide both operating sequences so the arrangement can be assessed without assuming that every motor reversal produces an opposite thrust load.

Should I choose back-to-back or face-to-face mounting?

Compare the required tilting stiffness, bearing spacing, housing alignment and assembly method. Back-to-back is often useful for a compact stiff support, while face-to-face is relatively more tolerant of misalignment. These general tendencies do not replace a review of the actual shaft and housing geometry.

Are two bearings with K08008AR0 references automatically a matched set?

No. The common part number does not prove that the two supplied bearings have been matched for the intended arrangement or preload. State the matching requirement on the quotation and order, and request the identification and installation instructions needed to preserve that set.

Can I reverse one bearing after the pair has been approved?

Changing orientation changes the support arrangement and can invalidate the matching or preload assumptions. Follow the approved set drawing and marks. If an orientation error is discovered, inspect and review the assembly before operation rather than treating the change as an interchangeable mounting choice.

How should a prototype be checked for push-pull accuracy?

Apply the agreed thrust in each direction and measure at the same functional datum through a defined loading sequence. Control temperature and the clamping state. Include the rest of the mechanism in the interpretation so that measured reversal movement is not automatically assigned entirely to the bearings.

Related angular-contact sizes

These smaller and larger Type A sizes provide alternate envelopes when reviewing an opposed support layout:

K05008AR0 / LYDL PA5008 — 50 × 66 × 8 mm · K12008AR0 / LYDL PA12008 — 120 × 136 × 8 mm

Request the drawing and quotation

Provide the forward and reverse thrust cases, radial loads, available pair spacing and desired mounting arrangement. Include the allowable reversal movement, operating temperature and required number of bearings or sets. LYDL can review PA8008 supply and matching requirements against those conditions.

Send your PA8008 inquiry to LYDL.

Official technical references

  1. KAYDON official catalog — metric Type A, printed page 73, with rating notes
  2. KAYDON metric part-number code definitions
  3. NSK N Series catalog — NBA angular-contact naming, printed pages 12–13

Brand Alternatives: THK · IKO · INA · Kaydon