CRBH8016A cross roller bearing / CRBHV8016A provides an 80 mm bore in a 120 mm outside diameter and 16 mm width. It bridges the smaller 13 mm profiles and the 10020A envelope. Match the IKO reference through LYDL when retaining an established machine layout, and define the required running accuracy before ordering.
Or email sales@luoyangdeeplink.com
The CRBH8016A cross roller bearing / CRBHV8016A size measures 80 × 120 × 16 mm. It occupies a useful position between the compact 13 mm wide group and the 20 mm wide 10020A. An equipment designer can review this profile when an 80 mm shaft or service opening is needed without immediately moving to a substantially larger outside diameter.
Its reference dynamic radial rating is 32.1 kN, static radial rating is 43.4 kN and mass is 0.74 kg. Those figures come from the IKO 8016A row. They describe the reference bearing, while the finished module’s useful load and positioning performance depend on its structure and operating cycle.
Check neighbouring envelopes in the CRBH / CRBHV size table; the series category groups the available product references.

Ordering the CRBH8016A / CRBHV8016A cross roller bearing? Send the drawing, the complete replacement reference or the required quantity. LYDL confirms the matched configuration, inspection scope and export terms in the quotation.
| Parameter | Value | Unit |
|---|---|---|
| Bore diameter d | 80 | mm |
| Outside diameter D | 120 | mm |
| Bearing width B | 16 | mm |
| Minimum chamfer rmin | 0.6 | mm |
| Inner-ring shoulder reference da | 88 | mm |
| Outer-ring shoulder reference Da | 112 | mm |
| Basic dynamic radial rating Cr | 32.1 | kN |
| Basic static radial rating C0r | 43.4 | kN |
| Reference bearing mass | 0.74 | kg |
The table identifies the 80 mm bore reference and its mounting shoulders. A 16 mm bearing profile does not include clamping plates or external protection. Catalogue load ratings do not describe installed running accuracy; agree the drawing and inspection requirement for the LYDL replacement.
Both catalogue-reference rings have an integrated construction. This reduces the assembly variables associated with separating a split ring, but it does not remove the need for flat seats and balanced retention. The standard size information should not be read as a promise of fixing holes in the rings.
For the CRBHV8016A reference, IKO describes a POM separator arrangement. Keep that requirement identifiable if it is part of the replacement specification. The plain CRBH8016A reference should follow the configuration required by the equipment, rather than an assumed material rule based on the missing V.
A sealed request needs its full suffix, not a note added after the model has been quoted. Likewise, running accuracy, internal clearance and lubricant should be recorded as independent purchasing requirements. They answer different engineering questions and should not be collapsed into a single description such as high precision.
Reference construction: catalogue [1] and product guide [2].
Compared with 7013A, this envelope adds 10 mm to the bore, 20 mm to the outside diameter and 3 mm to the width. The radial section increases from 15 mm to 20 mm. These are geometric changes, not a calculated improvement in system stiffness; their effect must be evaluated within the proposed housing.
For a compact robot axis, reserve space for the bearing retainers before placing the gearbox and encoder. The bearing width is only one part of the axial stack. Seal covers, fastener heads and assembly access can use the space that initially appeared available.
A tilting payload can create a varying overturning moment through the cycle. List the most demanding positions, not just the neutral pose. If motion reverses frequently, describe the travel angle and dwell periods so lubrication and torque requirements can be reviewed for that pattern.
The 0.6 mm minimum chamfer and the 88 mm and 112 mm shoulder dimensions are mounting references. Draw the adjoining corner radii and retaining faces explicitly. A corner that interferes with the bearing edge can prevent proper seating even when bore and outside diameter measurements are correct.
Choose between 7013A, 8016A and 10020A by available shaft diameter, radial space and axial width. Their names indicate different catalogue envelopes; none should be selected solely because its rating appears larger. Compare the load calculation and the amount of redesign required.
RU124 has the same 80 mm bore but uses a 165 mm outside diameter and a 22 mm width, with a different fixing arrangement. That makes it a useful mounting-design comparison where direct ring fastening is wanted. It is not a size-for-size replacement for 8016A.
| Size reference | Bore d (mm) | OD D (mm) | Width B (mm) |
|---|---|---|---|
| CRBH7013A / CRBHV7013A | 70 | 100 | 13 |
| CRBH10020A / CRBHV10020A | 100 | 150 | 20 |
If the rotating ring changes, compare the retention concept with RE split-inner-ring designs. For fixing-hole construction, RU124, 80 × 165 × 22 mm has the same bore but a much larger outside diameter and a different width.
Articulated automation: an 80 mm centre passage can support a joint layout with internal wiring. Allow space for the protective tube and cable movement instead of assuming the entire bore remains free.
Compact machine tools: an indexing or orienting axis should be assessed with cutting-force direction and fixture overhang included. Bearing selection alone does not define the stiffness of the cutting system.
Electronic production equipment: specify operating cleanliness, grease compatibility and permitted resistance at low speed. These requirements may determine the configuration as much as the dimensions do.
Medical laboratory mechanisms: define smooth positioning, cleaning exposure and maintenance access. Representative application artwork illustrates possible equipment types without identifying installed customers.
Application-family background: reference [3].

Check rotation after the retainers are tightened, because a free-bearing test does not reveal every mounting effect. If the installed torque changes significantly, review seating, alignment and clamping before treating the motor as the cause.
Inspection documents can be specified around the 80 mm bore, 120 mm outside diameter and 16 mm width, with separate rotational criteria where needed. Give the required datum ring and measurement setup so suppliers and receiving inspectors evaluate the same feature.
Keep the unit supported during unpacking and avoid touching protected raceway interfaces with contaminated tools. Individual identification, moisture protection and cushioning should remain effective until installation. Crate selection depends on quantity and transport handling, not only on the bearing’s 0.74 kg mass.

8016A has a 16 mm width and a 20 mm radial section. The extra axial and radial space must be provided in the housing. Check the retaining arrangement and the surrounding drive components rather than considering width in isolation.
Normally that requires redesign: RU124 is 80 × 165 × 22 mm, while 8016A is 80 × 120 × 16 mm. The common bore does not make their outside diameters, fixing details or axial stacks equivalent.
Possible causes include unequal clamping, a distorted seat, alignment error or an interference at a corner. Compare the assembled condition with the specified torque test. Do not remove material or change preload before the mounting condition has been reviewed.
No. State the travel angle, reversals, acceleration and dwell as well. An oscillating axis can have a very different duty from continuous rotation at an equivalent nominal speed, with different lubrication and torque considerations.
They are catalogue mounting references for the bearing geometry. The finished mating components need a complete drawing with seats, corner relief and retaining surfaces. Use the 88 mm and 112 mm references as part of that review, not as the entire housing specification.
Send LYDL the 8016A reference, mounting section and the larger-bore or wider-profile issue the design must solve. Include seal suffix, controlled ring, runout, clearance, loads and quantity. A useful replacement enquiry also gives the complete IKO designation from the existing unit. Specify required reports and the destination so the technical and packing details can be included in the quotation.
IKO is its owner’s trademark. LYDL supplies its own branded equivalent, matched to the complete reference configuration; the technical comparison does not imply IKO manufacture or endorsement.
Brand Alternatives: THK · IKO · INA · Kaydon